M-Bus (Meter-Bus) Protocol

Communications Output

M-Bus (Meter-Bus) is a European standard (EN 13757-2 physical and link layer, EN 13757-3 application layer) for the remote reading of water, gas and electricity meters.  The M-Bus interface has two wires, making it an easy and cost-effective AMR solution. A radio variant of M-Bus (Wireless M-Bus) is also specified in EN 13757-4. 

Electromagnetic Water Meters

The Electromagnetic water meter (Mag Meter) does not have any moving parts and is ideal for potable and wastewater applications or any dirty liquid which is conductive or water based. A magnetic field is applied to the metering tube, which results in a potential difference proportional to the flow velocity.

Woltmann Turbine Helical Vane Meters

Woltmann meters comprises of a rotor with helical blades inserted axially in the flow, much like a ducted fan; they can be considered a type of turbine flow meter. They are commonly referred to as helix meters and are usually used to measure bulk flows.

Combination Water Meters

Combination water meters comprises of a bulk Woltmann insert and a low-flow Volumetric insert or meter, flow is diverted between them by a by-pass valve that is set at a predetermined flow rate. This allows the combination meter to have a very large measurement range.

WRAS Approved Product

Whole products such as valves, boilers & showers undergo mechanical and water quality testing. This type of approval demonstrates full compliance with the requirements of the regulations and bye-laws, provided the fitting is installed according to any conditions given with the approval.

BSI BS EN 331 Approved Gas Product

BS EN 331:2015 specifies the characteristics for the construction, performance and safety of ball valves and closed bottom taper plug valves. It also details the test methods and marking provisions. It applies to metallic valves not directly buried for domestic and commercial installations inside or outside of buildings, using gases of the first, second and third family (specified in EN 437) and working up to 0,2 × 105 Pa, 0,5 × 105 Pa, 1 × 105Pa, 5 × 105 Pa and 20 × 105Pa and with temperature limits from – 5 °C or -20 °C to + 60 °C.

DNV-GL Type Approved Product

Classification, verification, risk management, and technical advisory to the maritime industry on safety, enhanced performance, fuel efficiency, etc. As a classification society, DNV GL sets standards for ships and offshore structures – known as Class Rules. They comprise safety, reliability and environmental requirements that vessels and other offshore mobile structures in international waters must comply with. DNV GL is authorized by 130 maritime administrations to perform certification or verification on their behalf.

Non-electrical devices and components group II

ATEX II 2 GD c T2 Non-electrical Valves

EC-Certificate is issued according to Article 8(1) b) ii) of Council Directive 94/9/EC for equipment and protective systems intended for use in potentially explosive atmospheres (ATEX).

Measurement Instrument Directive

Compliant Water Meter

Meters conform to the European Council Directive on Measurement Instruments which supersedes the Metrological Classes A, B, C etc. The permissible error limits are regulated across Europe by the MID, water meters may measure with an accuracy of +/-5% in the lower flow range and +/-2% in the permanent load range.

Elster Water Metering (Kent Meters)

Elster Water Metering (formally Kent Meters and now part of Honeywell) are an industry leader in the manufacture of water meters, which includes high accuracy mechanical meters, fully electronic water meters and Smart metering solutions for residential, commercial and industrial sectors.

Volumetric Positive Displacement Meter

Based on the volumetric rotary piston measurement principle, these meters offer the very highest levels of reading accuracy, even at the lowest flow rate. Optimum accuracy is maintained whether the meter is installed horizontally, vertically or on an incline.

ISO5211 Pad Mount for Actuator Operation

The top flange and drilling to ISO5211 specifications offer the widest possible selection of actuation options, as well as direct mount of pneumatic actuators and accessories.

Fire Safe Approved to API 607 4th Edition

Valves have been qualified by testing to API standards 607, 4th Edition. The valve design incorporates a secondary metal seat in the body, providing the required shutoff should the primary seats be destroyed by fire.

3.1 & 3.2 Material Certification (on request)

Many of our marine valves can be pressure tested, witnessed by a classification society and supplied with 3.1 & 3.2 certifications on request, these include Lloyd’s Register of Shipping, DNV-GL (Det Norske Veritas), RINA, Bureau Veritas, Germanischer Lloyds, NK and ABS (American Bureau of Shipping). Please contact sales with your requirements.

Multi-Jet Warm Water Meter

Multi-jet meters use multiple ports surrounding an internal chamber to create multiple jets of water against an impeller, whose rotation speed depends on the velocity of water flow. For best accuracy, they should be installed horizontally.